They are making a number of good pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this post directly below.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough project. If the old tub is conveniently available, the project can relocate easily; if you have to open up a wall to remove the old bathtub and position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the job and are comfortable trying it. Rather than hiring a service provider to take over a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you may require a professional plumber to make tube links.
This article will certainly aid you install a new bathtub in your washroom if you have actually currently acquired a new bathtub and also do not require to alter the plan of your previous water pipes.
Your devices and also product list need to consist of the following:
Preparing for the Installment
To start with, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is separate the water system. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Making use of both wood boards under its feet, put the tub in the required placement. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bathtub until the level reads degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub and likewise check the overflow outlet and the normal outlet for leakages.
Ultimately, repair the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bathtub must wait until the bathtub has actually been made use of at the very least once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in area between the tap and the sink. Secure the tap in place with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap ports. The previous kind should be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with moisture and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can break relatively very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads about Tools You Need to Install a New Bathtub , I was thinking sharing that blog post was valuable. In case you enjoyed our blog post please remember to pass it around. We treasure reading our article about How to Install a Bathtub Yourself.
Protect your property, call!